File Coverage

blib/lib/VIC/PIC/P16F690.pm

Criterion	Covered	Total	%
statement	44	53	83.0
branch	13	26	50.0
condition			n/a
subroutine	6	6	100.0
pod	0	2	0.0
total	63	87	72.4

package VIC::PIC::P16F690;
use strict;
use warnings;

our $VERSION = '0.32';
$VERSION = eval $VERSION;

use Carp;
use Moo;
extends 'VIC::PIC::Base';

# role CodeGen
has type => (is => 'ro', default => 'p16f690');
has include => (is => 'ro', default => 'p16f690.inc');

#role Chip
has f_osc => (is => 'ro', default => 4e6); # 4MHz internal oscillator
has pcl_size => (is => 'ro', default => 13); # program counter (PCL) size
has stack_size => (is => 'ro', default => 8); # 8 levels of 13-bit entries
has wreg_size => (is => 'ro', default => 8); # 8-bit register WREG
# all memory is in bytes
has memory => (is => 'ro', default => sub {
    {
        flash => 4096, # words
        SRAM => 256,
        EEPROM => 256,
    }
});
has address => (is => 'ro', default => sub {
    {
        isr => [ 0x0004 ],
        reset => [ 0x0000 ],
        range => [ 0x0000, 0x0FFF ],
    }
});

has pin_counts => (is => 'ro', default => sub { {
    pdip => 20, ## PDIP or DIP ?
    soic => 20,
    ssop => 20,
    total => 20,
    io => 18,
}});

has banks => (is => 'ro', default => sub {
    {
        count => 4,
        size => 0x80,
        gpr => {
            0 => [ 0x020, 0x07F],
            1 => [ 0x0A0, 0x0EF],
            2 => [ 0x120, 0x16F],
        },
        # remapping of these addresses automatically done by chip
        common => [0x070, 0x07F],
        remap => [
            [0x0F0, 0x0FF],
            [0x170, 0x17F],
            [0x1F0, 0x1FF],
        ],
    }
});

has registers => (is => 'ro', default => sub {
    {
        INDF => [0x000, 0x080, 0x100, 0x180], # indirect addressing
        TMR0 => [0x001, 0x101],
        OPTION_REG => [0x081, 0x181],
        PCL => [0x002, 0x082, 0x102, 0x182],
        STATUS => [0x003, 0x083, 0x103, 0x183],
        FSR => [0x004, 0x084, 0x104, 0x184],
        PORTA => [0x005, 0x105],
        TRISA => [0x085, 0x185],
        PORTB => [0x006, 0x106],
        TRISB => [0x086, 0x186],
        PORTC => [0x007, 0x107],
        TRISC => [0x087, 0x187],
        PCLATH => [0x00A, 0x08A, 0x10A, 0x18A],
        INTCON => [0x00B, 0x08B, 0x10B, 0x18B],
        PIR1 => [0x00C],
        PIE1 => [0x08C],
        EEDAT => [0x10C],
        EECON1 => [0x18C],
        PIR2 => [0x00D],
        PIE2 => [0x08D],
        EEADR => [0x10D],
        EECON2 => [0x18D], # not addressable apparently
        TMR1L => [0x00E],
        PCON => [0x08E],
        EEDATH => [0x10E],
        TMR1H => [0x00F],
        OSCCON => [0x08F],
        EEADRH => [0x10F],
        T1CON => [0x010],
        OSCTUNE => [0x090],
        TMR2 => [0x011],
        T2CON => [0x012],
        PR2 => [0x092],
        SSPBUF => [0x013],
        SSPADD => [0x093],
        SSPCON => [0x014],
        SSPSTAT => [0x094],
        CCPR1L => [0x015],
        WPUA => [0x095],
        WPUB => [0x115],
        CCPR1H => [0x016],
        IOCA => [0x096],
        IOCB => [0x116],
        CCP1CON => [0x017],
        WDTCON => [0x097],
        RCSTA => [0x018],
        TXSTA => [0x098],
        VRCON => [0x118],
        TXREG => [0x019],
        SPBRG => [0x099],
        CM1CON0 => [0x119],
        RCREG => [0x01A],
        SPBRGH => [0x09A],
        CM2CON0 => [0x11A],
        BAUDCTL => [0x09B],
        CM2CON1 => [0x11B],
        PWM1CON => [0x01C],
        ECCPAS => [0x01D],
        PSTRCON => [0x19D],
        ADRESH => [0x01E],
        ADRESL => [0x09E],
        ANSEL => [0x11E],
        SRCON => [0x19E],
        ADCON0 => [0x01F],
        ADCON1 => [0x09F],
        ANSELH => [0x11F],
    }
});

has pins => (is => 'ro', default => sub {
    my $h = {
        # number to pin name and pin name to number
        1 => [qw(Vdd)],
        2 => [qw(RA5 T1CKI OSC1 CLKIN)],
        3 => [qw(RA4 AN3 T1G OSC2 CLKOUT)],
        4 => [qw(RA3 MCLR Vpp)],
        5 => [qw(RC5 CCP1 P1A)],
        6 => [qw(RC4 C2OUT P1B)],
        7 => [qw(RC3 AN7 C12IN3- P1C)],
        8 => [qw(RC6 AN8 SS)],
        9 => [qw(RC7 AN9 SDO)],
        10 => [qw(RB7 TX CK)],
        11 => [qw(RB6 SCK SCL)],
        12 => [qw(RB5 AN11 RX DT)],
        13 => [qw(RB4 AN10 SDI SDA)],
        14 => [qw(RC2 AN6 C12IN2- P1D)],
        15 => [qw(RC1 AN5 C12IN1-)],
        16 => [qw(RC0 AN4 C2IN+)],
        17 => [qw(RA2 AN2 T0CKI INT C1OUT)],
        18 => [qw(RA1 AN1 C12IN0- Vref ICSPCLK)],
        19 => [qw(RA0 AN0 C1N+ ICSPDAT ULPWU)],
        20 => [qw(Vss)],
    };
    foreach my $k (keys %$h) {
        my $v = $h->{$k};
        foreach (@$v) {
            $h->{$_} = $k;
        }
    }
    return $h;
});

has clock_pins => (is => 'ro', default => sub {
    {
        out => 'CLKOUT',
        in => 'CLKIN',
    }
});

has oscillator_pins => (is => 'ro', default => sub {
    {
        1 => 'OSC1',
        2 => 'OSC2',
    }
});

has program_pins => (is => 'ro', default => sub {
    {
        clock => 'ICSPCLK',
        data => 'ICSPDAT',
    }
});

has io_ports => (is => 'ro', default => sub {
    {
        #port => tristate,
        PORTA => 'TRISA',
        PORTB => 'TRISB',
        PORTC => 'TRISC',
    }
});

has input_pins => (is => 'ro', default => sub {
    {
        #I/O => [port, tristate, bit]
        RA0 => ['PORTA', 'TRISA', 0],
        RA1 => ['PORTA', 'TRISA', 1],
        RA2 => ['PORTA', 'TRISA', 2],
        RA3 => ['PORTA', 'TRISA', 3], # input only
        RA4 => ['PORTA', 'TRISA', 4],
        RA5 => ['PORTA', 'TRISA', 5],
        RB4 => ['PORTB', 'TRISB', 4],
        RB5 => ['PORTB', 'TRISB', 5],
        RB6 => ['PORTB', 'TRISB', 6],
        RB7 => ['PORTB', 'TRISB', 7],
        RC0 => ['PORTC', 'TRISC', 0],
        RC1 => ['PORTC', 'TRISC', 1],
        RC2 => ['PORTC', 'TRISC', 2],
        RC3 => ['PORTC', 'TRISC', 3],
        RC4 => ['PORTC', 'TRISC', 4],
        RC5 => ['PORTC', 'TRISC', 5],
        RC6 => ['PORTC', 'TRISC', 6],
        RC7 => ['PORTC', 'TRISC', 7],
    }
});

has output_pins => (is => 'ro', default => sub {
    {
        #I/O => [port, tristate, bit]
        RA0 => ['PORTA', 'TRISA', 0],
        RA1 => ['PORTA', 'TRISA', 1],
        RA2 => ['PORTA', 'TRISA', 2],
        RA4 => ['PORTA', 'TRISA', 4],
        RA5 => ['PORTA', 'TRISA', 5],
        RB4 => ['PORTB', 'TRISB', 4],
        RB5 => ['PORTB', 'TRISB', 5],
        RB6 => ['PORTB', 'TRISB', 6],
        RB7 => ['PORTB', 'TRISB', 7],
        RC0 => ['PORTC', 'TRISC', 0],
        RC1 => ['PORTC', 'TRISC', 1],
        RC2 => ['PORTC', 'TRISC', 2],
        RC3 => ['PORTC', 'TRISC', 3],
        RC4 => ['PORTC', 'TRISC', 4],
        RC5 => ['PORTC', 'TRISC', 5],
        RC6 => ['PORTC', 'TRISC', 6],
        RC7 => ['PORTC', 'TRISC', 7],
    }
});

has analog_pins => (is => 'ro', default => sub {
        {
            # use ANSEL for pins AN0-AN7 and ANSELH for AN8-AN11
            #pin => number, bit
            AN0  => [19, 0],
            AN1  => [18, 1],
            AN2  => [17, 2],
            AN3  => [3,  3],
            AN4  => [16, 4],
            AN5  => [15, 5],
            AN6  => [14, 6],
            AN7  => [ 7, 7],
            AN8  => [ 8, 8],
            AN9  => [ 9, 9],
            AN10 => [13, 10],
            AN11 => [12, 11],
        }
});

has adc_channels => (is => 'ro', default => 12);
has adcs_bits  => (is => 'ro', default => sub {
    {
        2 => '000',
        4 => '100',
        8 => '001',
        16 => '101',
        32 => '010',
        64 => '110',
        internal => '111',
    }
});
has adc_chs_bits => (is => 'ro', default => sub {
        {
            #pin => chsbits
            AN0  => '0000',
            AN1  => '0001',
            AN2  => '0010',
            AN3  => '0011',
            AN4  => '0100',
            AN5  => '0101',
            AN6  => '0110',
            AN7  => '0111',
            AN8  => '1000',
            AN9  => '1001',
            AN10 => '1010',
            AN11 => '1011',
            CVref => '1100',
            '0.6V' => '1101',
        }
});

has timer_prescaler => (is => 'ro', default => sub {
    {
        2 => '000',
        4 => '001',
        8 => '010',
        16 => '011',
        32 => '100',
        64 => '101',
        128 => '110',
        256 => '111',
    }
});

has wdt_prescaler => (is => 'ro', default => sub {
    {
        TMR0 => {
            1 => '000',
            2 => '001',
            4 => '010',
            8 => '011',
            16 => '100',
            32 => '101',
            64 => '110',
            128 => '111',
        },
        WDT => {
            32 => '0000',
            64 => '0001',
            128 => '0010',
            256 => '0011',
            512 => '0100',
            1024 => '0101',
            2048 => '0110',
            4096 => '0111',
            8192 => '1000',
            16384 => '1001',
            32768 => '1010',
            65536 => '1011',
            ## others are reserved
        },
        LFINTOSC => 31000, #31kHZ
    }
});

has timer_pins => (is => 'ro', default => sub {
    {
        #reg     #reg      #ireg #flag  #enable
        TMR0 => { reg => 'TMR0', freg => 'INTCON', flag => 'T0IF', enable => 'T0IE', ereg => 'INTCON' },
        TMR1 => { reg => ['TMR1H', 'TMR1L'], freg => 'PIR1', ereg => 'PIE1', flag => 'TMR1IF', enable => 'TMR1E' },
        TMR2 => { reg => 'TMR2', freg => 'PIR1', flag => 'TMR2IF', enable => 'TMR2IE', ereg => 'PIE1' },
        T0CKI => 17,
        T1CKI => 2,
        T1G => 3,
    }
});

has eccp_pins => (is => 'ro', default => sub {
    {   # pin => pin_no, tris, bit
        P1D => [14, 'TRISC', 2],
        P1C => [7, 'TRISC', 3],
        P1B => [6, 'TRISC', 4],
        P1A => [5, 'TRISC', 5],
        CCP1 => [5, 'TRISC', 5],
    }
});

#external interrupt
has eint_pins => (is => 'ro', default => sub {
    {
        INT => 17,
    }
});

has ioc_pins => (is => 'ro', default => sub {
    {
               #pin #ioc-bit #ioc-reg
        RA0 => [19, 'IOCA0', 'IOCA'],
        RA1 => [18, 'IOCA1', 'IOCA'],
        RA2 => [17, 'IOCA2', 'IOCA'],
        RA3 => [4,  'IOCA3', 'IOCA'],
        RA4 => [3,  'IOCA4', 'IOCA'],
        RA5 => [2,  'IOCA5', 'IOCA'],
        RB4 => [13, 'IOCB4', 'IOCB'],
        RB5 => [12, 'IOCB5', 'IOCB'],
        RB6 => [11, 'IOCB6', 'IOCB'],
        RB7 => [10, 'IOCB7', 'IOCB'],
    }
});

has ioc_ports => (is => 'ro', default => sub {
    {
        # for ports to be used as well
        PORTA => 'IOCA',
        PORTB => 'IOCB',
        FLAG => 'RABIF',
        ENABLE => 'RABIE',
    }
});

has usart_pins => (is => 'ro', default => sub {
    {
        async_in => 'RX',
        async_out => 'TX',
        sync_clock => 'CK',
        sync_data => 'DT',
        rx_int => { reg => 'PIE1', flag => 'RCIF', enable => 'RCIE', preg =>
            'INTCON', penable => 'PEIE' },
        tx_int => { reg => 'PIR1', flag => 'TXIF', enable => 'TXIE', preg =>
            'INTCON', penable => 'PEIE' },
        # this defines the port names that the user can use
        # validly. The port names define whether the user wants to use them in
        # synchronous or asynchronous mode
        UART => 'async',
        USART => 'sync',
    }
});

sub usart_baudrates {
    my ($self, $baud, $f_osc, $sync) = @_;
    $baud = 9600 unless defined $baud;
    my %acceptable = map { $_ => 1 } (300, 1200, 2400, 9600, 19200, 57600, 115200);
    unless (exists $acceptable{$baud}) {
        my $str = sprintf "Baud rate %d is unacceptable. Allowed rates are: %s",
        $baud, join(',', keys %acceptable);
        carp $str;
        return;
    }
    $f_osc = defined $f_osc ? $f_osc : $self->f_osc;
    $sync = defined $sync ? $sync : 0;
    ## we check with the expected error rates and pick the appropriate baud-rate
    ## generation parameters such as the values of BRG16 and BRGH
    if ($sync) {
        # BRGH = x, BRG16 = 1
        my $spbrg = int(($f_osc / ($baud * 4)) - 1);
        my $cbaud = int($f_osc / (($spbrg + 1) * 4));
        my $error = (($cbaud - $baud) * 100) / $baud;
        return { SPBRG => $spbrg, BRGH => 0, BRG16 => 1,
                error => $error, actual => $cbaud, baud => $baud };
    } else {
        # BRG16 = 0, BRGH = 0, BRG is 8-bit
        my $spbrg_00 = int(($f_osc / ($baud * 64)) - 1);
        my $cbaud_00 = $f_osc / (($spbrg_00 + 1) * 64);
        my $error_00 = (($cbaud_00 - $baud) * 100) / $baud;
        my $hh_00 = { SPBRG => $spbrg_00, error => $error_00, actual => $cbaud_00,
                      BRG16 => 0, BRGH => 0, baud => $baud } if $spbrg_00 < 0x100;
        # BRG16 = 0, BRGH = 1, BRG is 8-bit
        my $spbrg_01 = int(($f_osc / ($baud * 16)) - 1);
        my $cbaud_01 = $f_osc / (($spbrg_01 + 1) * 16);
        my $error_01 = (($cbaud_01 - $baud) * 100) / $baud;
        my $hh_01 = { SPBRG => $spbrg_01, error => $error_01, actual => $cbaud_01,
                      BRG16 => 0, BRGH => 1, baud => $baud } if $spbrg_01 < 0x100;
        # BRG16 = 1, BRGH = 0, BRG is 16-bit
        my $spbrg_10 = int(($f_osc / ($baud * 16)) - 1);
        my $cbaud_10 = $f_osc / (($spbrg_10 + 1) * 16);
        my $error_10 = (($cbaud_10 - $baud) * 100) / $baud;
        my $hh_10 = { SPBRG => $spbrg_10, error => $error_10, actual => $cbaud_10,
                      BRG16 => 1, BRGH => 0, baud => $baud } if $spbrg_10 < 0x10000;
        # BRG16 = 1, BRGH = 1, BRG is 16-bit
        my $spbrg_11 = int(($f_osc / ($baud * 4)) - 1);
        my $cbaud_11 = $f_osc / (($spbrg_11 + 1) * 4);
        my $error_11 = (($cbaud_11 - $baud) * 100) / $baud;
        my $hh_11 = { SPBRG => $spbrg_11, error => $error_11, actual => $cbaud_11,
                      BRG16 => 1, BRGH => 1, baud => $baud } if $spbrg_11 < 0x10000;
        ## sort based on error in ascending order and remove NaN
        my @sorted = sort { $a->{error} <=> $b->{error} }
                     grep { defined $_ and $_->{error} == $_->{error} } ($hh_00, $hh_01, $hh_10, $hh_11);
        unless (@sorted) {
            carp "Cannot seem to find appropriate baud generator values for $baud";
            return;
        }
        return wantarray ? @sorted : $sorted[0];
    }
}

has selector_pins => (is => 'ro', default => sub {
    {
        'spi_or_i2c' => 'SS',
    }
});

has spi_pins => (is => 'ro', default => sub {
    {
        data_out => 'SDO',
        data_in => 'SDI',
        clock => 'SCK',
    }
});

has i2c_pins => (is => 'ro', default => sub {
    {
        data => 'SDA',
        clock => 'SCL',
    }
});

has cmp_input_pins => (is => 'ro', default => sub {
    {
        'C1IN+' => 'C1IN+',
        'C12IN0-' => 'C12IN0-',
        'C2IN+' => 'C2IN+',
        'C12IN1-' => 'C12IN1-',
        'C12IN2-' => 'C12IN2-',
        'C12IN3-' => 'C12IN3-',
    }
});

has cmp_output_pins => (is => 'ro', default => sub {
    {
        C1OUT => 'C1OUT',
        C2OUT => 'C2OUT',
    }
});

has chip_config => (is => 'ro', default => sub {
    {
        on_off => {
            MCLRE => 0,
            WDT => 0,
            PWRTE => 0,
            CP => 0,
            BOR => 0,
            IESO => 0,
            FCMEN => 0,
        },
        f_osc => {
            INTRC_OSC => 0,
        },
    }
});

my @rolenames = qw(CodeGen Operators Chip GPIO ADC ISR Timer Operations ECCP
                    USART SPI I2C Comparator Power);
my @roles = map (("VIC::PIC::Roles::$_", "VIC::PIC::Functions::$_"), @rolenames);
with @roles;

sub list_roles {
    my @arr = grep {!/CodeGen|Oper|Chip|ISR/} @rolenames;
    return wantarray ? @arr : [@arr];
}

1;
__END__